您好,歡迎進入丹東奧龍射線儀器集團有限公司網站!
                          一鍵分享網站到:
                          產品列表

                          —— PROUCTS LIST

                          相關新聞

                          —— NEWS

                          產品中心Products 當前位置:首頁 > 產品中心 > X射線晶體定向儀 > X射線晶體粘料定向儀 > 晶棒參考面X射線定向儀

                          晶棒參考面X射線定向儀

                          晶棒參考面X射線定向儀

                          更新時間:2023-09-14

                          產品型號:ALL-CKMD400型

                          廠商性質:生產廠家

                          生產地址:

                          產品報價:

                          產品特點:晶棒參考面X射線定向儀的結構與功能介紹:基準平臺:此件固定在主機的臺面板上,測量時做水平基準面,基準平臺的右側為定位面,左側為夾緊裝置,左側的夾緊裝置上有夾緊螺釘,設備配套的夾具在測量時放于基準平臺上。

                          產品詳情

                          ALL-CKMD400型晶棒參考面X射線定向儀

                          ALL-CKMD 400 MODEL X-RAY CRYSTAL ORIENTATION INSTRUMENT BY THE REFERENCE PLANE

                           

                          晶棒參考面X射線定向儀產品特點

                            測量晶棒夾具的結構與功能介紹:

                          基準平臺:此件固定在主機的臺面板上,測量時做水平基準面,基準平臺的右側為定位面,左側為夾緊裝置,左側的夾緊裝置上有夾緊螺釘,設備配套的夾具在測量時放于基準平臺上。

                            測量<A>面:晶體主參考面<A>面定向:可測量晶棒直徑為2、4、6英寸,<A>面的θ角:18.917°(18°5500)(或按客戶需要做C向、R)。

                          ①儀器的校準:用標準晶棒校準儀器。晶向<A>的θ角:18.917° (18°5500)

                          ②將裝有晶棒的夾具,清理潔凈后放到儀器的基準平臺上,調整前后位置,使X光能夠照射到晶棒的外圓柱面上,旋轉基準平臺左側的夾緊螺釘,把緊。打開X射線光閘,使待測量晶棒在夾具內慢慢轉動,尋測峰值。當μA表針為*狀態時(即為zui大值時),保證晶棒不動,夾緊晶棒。

                          ③將夾具從定向儀下移出,轉到磨床上磨削平面。

                          ④自動升降測試。

                           

                          Features

                          Construction and function of crystal clip

                          Benchmark platforms: it is fixed on the host machine panel, used for the horizontal platform when testing the sample.The right side of the base platform for locating surface, left platform for clamping .The clip has the screw clamping device.Please put the clip on the horizontal platform when begin to have a testing .

                          Measuring the < A > direction : crystal main reference < A > flat orientation: it can measure crystal rods for 2, 4, 6 inch in diameter, <A> direction θ angle18.917°(18 ° 55 '00 ") (or according to customers requirement ,use the C or R direction).

                          The calibration of instruments: use a standard crystal rod calibration instrument. Crystal (A) θ Angle :18.917 ° (18 ° 55 00 ")

                          After cleaning up the clip ,and put it on the horizontal platform for adjusting its position ,in order to enable the x-ray exposure on the outside skin of the cylinder crystal ,and fix the screw on the left of rotated horizontal.Open the X-ray shutter ,and let the crystal rotating slow to find the peak .When the μA meter find the best status (i.e the max.value) ,make sure the crystal being static,and fix it tightly.

                          Unload the clip from the instrument ,and put it on the grinding plane of the grinding machine.

                          Auto lifting test.

                           

                          晶棒參考面X射線定向儀技術指標

                          ●輸入電源:單相交流220V,50Hz,0.25kW。

                          X射線管:銅靶,風扇冷卻,陽極接地。

                          ●zui大管電壓電流:30kV,5mA連續可調,使用2.0mA以上,

                                            有可能損壞X光管并加大輻射危害。  

                          ●探測器:計數器。工作電壓zui高為DC1000V;或閃爍探測器,

                                             工作電壓zui高為DC1200V。

                          ●時間常數:1(快)、2(慢)兩檔。

                          ●測角角度:θ=18.917°(18°5500″)

                          ●主光閘:自動。

                          ●顯示板:射線強度表。

                          ●外型尺寸:1132(長)×642(寬)×1460(高)mm

                          ●重量:200kg

                           

                          Technical Parameters

                          Input power: Single phase with AC 220V,50Hz,0.25kW

                          X-ray tube : Cu target ,cooled by fan ,and anode earth

                          Max.tube voltage and current :30kV ,5mA ,being continued adjustment .If using the current is more than 2.0mA ,which may be damaged the X-ray tube insert and enlarge the radiative harm

                          Detector: counter . The max. working voltage is DC1000V;Or scintillation counter,the max.working voltage is DC1200V

                          Time parameter:1(fast)/2(low)

                          Testing angel :θ=18.917°(18°5500″)

                          Main shutter:auto

                          Displaying board: radiative rose chart

                          Size:1132L)×642W)×1460Hmm

                          Weight:200kg

                           

                           

                           如果你對ALL-CKMD400型晶棒參考面X射線定向儀感興趣,想了解更詳細的產品信息,填寫下表直接與廠家聯系:

                          留言框

                          • 產品:

                          • 您的單位:

                          • 您的姓名:

                          • 聯系電話:

                          • 常用郵箱:

                          • 省份:

                          • 詳細地址:

                          • 補充說明:

                          • 驗證碼:

                            請輸入計算結果(填寫阿拉伯數字),如:三加四=7
                          版權所有 © 2024 丹東奧龍射線儀器集團有限公司  ICP備案號:遼ICP備09002145號-3
                          国产精品国产三级国产AV主播_中国少妇内射XXXXⅩHD_欧美叉叉叉BBB网站_丰满少妇又硬又粗又大视频